3D Printer Parts & Accessories
3D Printer Parts & Accessories
5-8mm ALUMINIUM FLEXIBLE SHAFT COUPLING 5MM TO 8MM
Couple 5mm shaft * 8mm shaft.15 grams. -- These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they are not perfectly co-linear...
Rs. 200.00
Rs. 109.00
5-10mm ALUMINIUM FLEXIBLE SHAFT COUPLING 5mm to 10mm
Couple 5mm shaft * 10mm shaft. 15 grams.--These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they are not perfectly co-linear and...
Rs. 200.00
Rs. 109.00
Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module
PWM capability of up to 25 kHz combined with active freewheeling. Switched mode current limitation for reduced power dissipation in overcurrent Overtemperature shut down with latch behavior. Undervoltage shut down. Overvoltage lockout. The Double BTS7960 43A H-Bridge High-Power Stepper Motor...
Rs. 1,100.00
Rs. 299.00
5-6mm ALUMINIUM FLEXIBLE SHAFT COUPLING 5mm to 6mm
Bore Diameter(D1)=5mm, D2=6mm Exhibits good strength. High-grade aluminum couplings. Weight 15 grams. -- These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they...
Rs. 200.00
Rs. 109.00
ULN2003 Stepper Motor Driver Board
ULN2003A motor driver chip Chip all the pins already leads for easy connection to use 5-12V power supply 4-way signal indicator XH-5P socket can be connected directly 28BYJ-48 Model stepper motor This is the ULN2003 Driver Module Stepper Motor Driver...
Rs. 150.00
Rs. 75.00
8-10mm ALUMINIUM FLEXIBLE SHAFT COUPLING 8mm to 10mm
Bore Diameter(D1)=8mm, D2=10mm Exhibits good strength. High-grade aluminum coupler Weight 15 grams. -- These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they...
Rs. 200.00
Rs. 109.00
28BYJ-48 DC 5V Stepper Motor Step Motor
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm Note: The system is recommended to run on Half-step mode(8 step control signal sequence) for excellent performance...
Rs. 300.00
Rs. 149.00
28BYJ-48 Stepper Motor DC 12V
28BYJ-48 -12V DC Stepper Motor This 12V DC 28BYJ-48 Stepper Motor is a small, inexpensive, and high-quality geared step motor. The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper...
Rs. 300.00
Rs. 149.00
8-8mm ALUMINIUM FLEXIBLE SHAFT COUPLING 8mm to 8mm
Bore Diameter(D1)=8mm, D2=8mm Exhibits good strength. High-grade aluminum couplings. Weight 15gm -- These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they...
Rs. 200.00
Rs. 109.00
DRV8825 Stepper Motor Driver with Aluminum Heat Shrink for 3D printer
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight:...
Rs. 180.00
Rs. 125.00
TB6600 Stepper Motor Driver Controller
Input Current: 0~5A Output Current: 0.5~4.0A Control Signal: 3.3~24V Power (MAX): 160W Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32 Temperature: -10~45℃ H bridge bipolar constant current drive. TB6600 Arduino Stepper Motor Driver is an easy-to-use professional stepper motor...
Rs. 880.00
Rs. 469.00
0.4 mm Nozzle V6 Type for 3D Printer Brass Nozzle (Pack of 1)
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Nozzle Accuracy: 0.4mm Screw outer diameter: M6 This is a universal 3D printer Hot End Nozzle with a diameter of 0.4mm designed to be used with a 1.75mm PLA, ABS, Flex and Nylon filaments....
Rs. 130.00
Rs. 49.00
6-8mm ALUMINIUM FLEXIBLE SHAFT COUPLING 6MM TO 8MM
Couple 6mm shaft * 8mm shaft.15 grams. -- These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they are not perfectly co-linear...
Rs. 200.00
Rs. 109.00
ULN2003 Stepper Motor Driver Board Red
ULN2003A motor driver chip Chip all the pins already leads for easy connection to use 5-12V power supply 4-way signal indicator XH-5P socket can be connected directly 28BYJ-48 Model stepper motor This is the ULN2003 Driver Module Stepper Motor Driver...
Rs. 150.00
Rs. 49.00
SC8UU 8 mm Linear Ball Bearing Slide Unit CNC 3D Printer
Product Name: Linear Bearing Model: SC8UU Material: Metal, Rubber ID: 8mm. Model - SC8UU Material - Metal + Rubber Inner Diameter (ID) (mm) - 8 Length (mm) -30 Width (mm) -34 Height (mm) - 22 Weight (gm) - 44 An SC8UU 8mm Linear Ball...
Rs. 250.00
Rs. 229.00
NEMA 17 Stepper Motor - 34mm
3D printer motor with high torque 59Ncm(83.6oz.in) holding torque NEMA 17 bipolar 1.65"x1.65"x1.85" 4-wire Build with 1m Cable and 0.1" pitch Connector Rated current 2.0A & resistance 1.4ohms--Stepper Motor – 1.5A – 34mm is the most popular motors used to...
Rs. 1,250.00
Rs. 999.00
1.0 mm Nozzle for 3D Printer Brass Nozzle (Pack of 1)
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Nozzle Accuracy: 1.0 mm Screw outer diameter: M6 This is a universal 3D printer Hot End Nozzle with a diameter of 1.0mm designed to be used with a 1.75mm PLA, ABS, Flex and Nylon...
Rs. 130.00
Rs. 49.00
5-5mm Blue Aluminum Alloy Coupling 5x5MM for 3D Printers and CNC Machines
The Aluminum Alloy Coupling 5x5mm for 3D Printers and CNC Machines is lightweight coupling and exhibits more strength in class. This type of couplings is very common and found in a wide range of CNC Machines. The bore diameters of...
Rs. 200.00
Rs. 99.00
250mm Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut
Lead Screw Material: 304 Stainless Steel. Length: 250mm. Diameter: 8mm. 4 Start Lead Screw Brass Nut Size: 10 x 13 x 22 mm. Mainly use for Stepping motor driving guide rail. T shape design, made of high-quality stainless steel material....
Rs. 550.00
Rs. 399.00
8mm Bore Inner Ball Mounted Pillow Block Insert Bearing KP08
Type: KP08
Material: zinc alloy
Bore Diameter:8mm
Mounting Hole Diameter: 5 mm
Durable with high precision
Can withstand great weight
Rs. 230.00
Rs. 169.00
GT2-6mm Belt Width 20 Teeth 5mm Bore Timing Pulley
Outer Diameter: 16mm
Inner Diameter: 5mm
High-Quality Aluminium
Excellently Machined
Durable and practical
Minimizes the chance of the belt slipping
Rs. 160.00
Rs. 119.00
0.6 mm Nozzle for 3D Printer Brass Nozzle (Pack of 1)
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Nozzle Accuracy: 0.6mm Screw outer diameter: M6 This is a universal 3D printer Hot End Nozzle with a diameter of 0.6mm designed to be used with a 1.75mm PLA, ABS, Flex and Nylon filaments....
Rs. 130.00
Rs. 49.00
NEMA 17 17HS4401 Stepper Motor (4.4 kg-cm) - 40mm
The stepper motors move in precisely repeatable steps, hence they are the motors of choice for the machines requiring precise position control. The NEMA17 4.8 kg-cm Stepper Motor can provide 4.8 kg-cm of torque at 2.5A current per phase. The...
Rs. 999.00
Rs. 649.00
NEMA 17 Stepper Steel and Rubber Vibration Dampers clamp
This damper is for NEMA 17 stepper motors. It can effectively reduce noise and vibration generated from the running stepper motors.
Rs. 100.00
Rs. 60.00
Showing 1 - 24 of 64 total